Installation Instructions - Natural Roller Shades

Thank you for purchasing Natural Roller Shades.

With proper installation, your shades should look beautiful and provide years of service. Please check all parts and review this manual before starting installation.

NOTE: If installing motorized shades, the motorization manual is provided separately. Please refer to that manual for instructions on programming and operating motorized shades.

TOOLS THAT MAY BE REQUIRED: Pencil, Tape Measure, Drill, Screw Driver, Level and Step Stool

NOTE: For drywall (wallboard) or plaster, use anchors designed for hollow walls (not included). For concrete, stone, and brick, use a masonry drill bit and masonry anchors (not included).

Shade Care And Cleaning

Because of the material content for these fabrics, steaming and spot cleaning is not recommended.

When dusting is required, be sure to use something gentle. We recommend using a vacuum brush or a duster.

Following these tips will help to extend the life of your shades and ensure that they stay beautiful for years to come.

______________________________________________________________________________________________________________

Standard Open Roll (Single Shades)

If open roll shade was ordered with a Box Valance, see Box Valance installation before starting installation.

STEP 1: INSTALL BRACKETS

Roller shade brackets can be installed to the wall (face mount) or to the ceiling or underside of the window recess (top mount). 

Determine the desired location for the brackets. Mark the position of the brackets and ensure they are the correct distance apart and that they are level and in line with each other. 

STEP 2: INSTALL SHADE
Insert the control side of the shade into the control end bracket, ensuring the lug on the bracket fits into the slot. Then, push in the pin on the idle end of the shade and move the shade up so that the pin engages with the hole in the idle end bracket. When the pin snaps into the bracket, the shade is securely installed.

NOTE: Cordless open roll shades must be fully rolled on the tube before installation. If not fully rolled on the tube, the shade will not raise completely in operation. Cordless open roll brackets must also be installed at exactly the ordered width for the shade to operate properly. 

NOTE: CHAIN TENSIONER INSTALLATION 

Shades with clutch controls come with a continuous chain loop, which MUST be secured to the wall with the included chain tensioner. 

See separate instructions for Chain Tensioner Installation. 

______________________________________________________________________________________________________________

Dual Bracket (Double Shades)

If dual shade was ordered with a Box Valance, see Box Valance installation before starting installation.

STEP 1: INSTALL BRACKETS

Dual roller shade brackets can be installed to the wall (face mount) or to the ceiling or underside of the window recess (top mount). 

Determine the desired location for the brackets. Mark the position of the brackets and make sure they are the correct distance apart and that they are level and in line with each other. 

STEP 2: INSTALL SHADE

Install the bottom shade followed by the top shade. The shade installed on the bottom of the bracket will always be standard roll. The shade installed on the top of the bracket will always be reverse roll. 

Insert the control side of the shade into the control end bracket, ensuring the lug on the bracket fits into the slot. Then, push in the pin on the idle end of the shade and move the shade up so that the pin engages with the hole in the idle end bracket. When the pin snaps into the bracket, the shade is securely installed. 

NOTE: Cordless open roll shades must be fully rolled on the tube before installation. If not fully rolled on the tube, the shade will not raise completely in operation. Cordless open roll brackets must also be installed at exactly the ordered width for the shade to operate properly. 

NOTE: CHAIN TENSIONER INSTALLATION 

Shades with clutch controls come with a continuous chain loop, which MUST be secured to the wall with the included chain tensioner. 

See separate instructions for Chain Tensioner Installation. 

______________________________________________________________________________________________________________

Open Roll - Decorative Metal Brackets

Note (Wand Motor Installations): If installing brackets with wand motors, brackets must be installed top mount. Wand controls must be installed to the motor head prior to installing the wand motor control side to the bracket.

Note (Cordless Installations): Cordless open roll shades must be fully rolled on the tube before installation. If not fully rolled on the tube, the shade will not raise completely in operation. Cordless open roll brackets must also be installed at exactly the ordered width for the shade to operate properly. 

STEP 1: INSTALL BRACKETS

1.  Installation brackets are equipped to fit either the idle end or control end of your shade. 

2. The brackets can be installed to the wall (face mount) or to the ceiling or underside of the window recess (top mount).  

3. Determine the location for the brackets and the mounting style. Mark the position of the brackets and confirm they are the correct distance apart. Confirm brackets are level and in line. 

4. Once the brackets are installed, cover the installation screws on the foot of the bracket with screw covers. 

STEP 2: INSTALL SHADE

1. Insert the motor head into the control end bracket. 

2.  The idle end of the shade has a dial which can be turned to retract the idle end pin. Once the pin is retracted, the idle end can be aligned with the opening of the idle end bracket. Once in place, turn the dial to release the idle end pin to hold the shade in place. 

3. If your shade requires removal after installation, turn the dial on the idle end to retract the idle end pin and remove the shade from the brackets.